Archive

Category Archives for "Lights"

How To Install Fog Light DIY In 5 Easy Steps

Fog lights are lights particularly intended to enable the driver to see the street through the fog. The Fog lights are an extraordinary beam-sort molded lights and mainly comes in a bar shape. They have beams which are ground level and are wide to permit most extreme visibility even in thick fog. They are typically set in the lower segment of the car to enable the driver to see the street. The best fog Lights are generally set close to the guard of the vehicle. They come in yellow and white lights.

The installation process of fog lights is straightforward. There can be two alternatives, whether you want to wire it onto a different switch or on the same one from the headlights. Generally individuals who work in fog-inclined regions complete the wiring to the headlights as it is a better alternative.

Step 1: Disconnecting The Ground Terminal of The Battery

In every situation where you do any sort of wiring to your vehicle, dependably separate the ground terminal on the battery as this is a safety direction and in addition takes into account a better set up as you would not need to stress over being shocked.

Step 2: Place Fog Lights On Their Spot

Pick the mounting area for your fog lights. Generally these lights are put on the guard yet put it according to your requirement and use. It is best to put the fog lights incidentally first before you connect the lights for all time so you can transform it later if required.

Step 3: Place The Switch In The Desired Location

After you have put the fog lights in the coveted place, put the switch in an area which would be advantageous to the driver to turn on and off.

Step 4: Wiring the fog lights with a different switch

The wire that originates from under the dash, connect that with the switch terminal on the lights. Presently connect the battery terminal on the lights to the battery. At that point connect the ground terminal on the change to the metal part under the dash. From that point onward, interface the load side of the switch with a wire. Take this wire through the firewall into the engine compartment and interface it to battery. After you are finished with the wiring procedure, check if all the wiring is secure. Re-interface the ground terminal of the battery.

Step 5: Reconnect the ground terminal of the battery

Once the setup is secure, reconnect the battery and test if the setup is working fine. Switch off the lights twice or thrice to confirm if there is no loose wiring or any flickering.

Fog Lights are particularly easy to install. If you do not have an idea of handling wires before, try and ask for guidance so that you do not mess up your vehicle. Safety comes first so always keep your hands dry while wiring.

How To Wire Fog Lights Without A Relay

Fog lights are the kind of lights built to aid the driver see the road even in fog conditions. The fog lights have a beam shape. The light steak by the fog lights are flat which provides a good range and visibility in extreme fog weather. They are most often mounted on the bumper of a vehicle which offers for a good lighting distance from the road and provides a good beam. They come in yellow and white lights. You can choose which will fit you best as per the vehicle you are using it on and as per the traffic rules of your state.

When you plan to wire fog lights on your own, you have two options, whether you want to wire it onto a separate switch or wire it via a relay. In general, people use a relay to wire a fog lights because it is more useful and easier to use. If you are not much of a fog-light user and want to save the money you would spend on a relay here are step by step instructions on how how to wire fog lights without using a relay:

Step 1: Disconnecting the battery

Whenever you are wiring or doing any technical work with your car wiring, the first step is to disconnect the ground terminal on the battery for safety reasons and also because you can do your work without the fear of being electrocuted from the current from the battery

Step 2: On-board the lights on desired location

As mentioned, fog lights are most often placed on the bumper. As per your vehicle design, place the lights on the location you think is most suitable.

Step 3: Switch Placement

Once you place the fog lights in the right location, attach the switch in a location which would be easy for the driver to access and switch on and off swiftly.

Step 4: Wiring the fog lights without a relay

Since you would not be using a relay, connect the wire which comes under the dash to the switch terminal on the lights directly. Not using a relay eliminates the process of having to connect everything to the relay and the control is shifted to the switch directly. After this, connect the battery terminal on the lights to the battery. Now you need to connect the ground terminal on the switch to the metal part under the dash. Now connect the load side of the switch with a wire. You now need to take this wire through the firewall into the engine compartment and connect it to battery.

Step 5: Reconnect the battery

Always double check if all the wiring is secure. Re-connect the ground terminal of the battery.

Unless you want to save on cost, it is always more advisable to use a relay as you get the power to control the beam as per your requirement which saves on battery and gives a better driving experience.

How to turn on fog lights

If you are prone to driving areas with fog, mist and heavy rains, you must have already got Fog Lights set up on to your vehicle bumper. It is not useful but also important but also provides safety against road bumps and blocks. Usually these lights would be wired to your headlights. They do not come pre-equipped and always have to be added externally. Only in some heavy duty vehicles, they are pre-equipped. In order to turn on the fog lights, if you follow these simple steps, you can turn them on as soon as you are in the need for it.

Step 1

Switch on your headlights. Without the headlights being on, the fog lights are also automatically off.

Step 2

Keep the headlights on the low beam end. This is important and essential as the fog lights will only function when the headlights are on low beam. It would not work if the headlights are on high beam.

Step 3

There will be an inner ring on the turn signal level which is connected to the fog lights. Locate the inner ring.

Step 4

There will usually be fog light symbol attached. Switch it on.

Step 5

Similarly turn the inner ring off when you do not need the fog lights anymore. Please keep in mind that if you use the fog lights or use it unnecessarily in a pleasant weather, it may blind the other drivers as the beam is quite strong. Only use the lights in weather conditions which require it.

If you just got your fog lights installed, try turning them off and on several times before you actually hit the road to get the idea of how it works and so that you can use it instantly when required.

How To Wire Fog Lights

Fog lights are lights specifically designed to help the driver see the road through the fog. The Fog lights are a special beam-type shaped lights and usually comes in a narrow bar shape. They have beams which are flat and are wide to allow maximum visibility even in dense fog. They are usually placed in the lower portion of the car to allow the driver to see the road. The Fog Lights are mostly placed near the bumper of the vehicle. They come in yellow and white lights depending upon the rules and the utility.

The process of wiring fog lights is actually quite simple. There can be two options, whether you want to wire it onto a separate switch or on the same one as the headlights. Usually people who work in fog-prone areas get the wiring done to the headlights as they are used together. If you follow this step-by-step process on how to wire fog lights, it becomes much easier to install it on your own.

Step 1: Disconnecting The Battery

In all the cases where you do any kind of wiring to your vehicle, always disconnect the ground terminal on the battery as this is a safety instruction as well as allows for a better set up as you would not have to worry about being electrocuted.

Step 2: Mounting Fog Lights

Choose the mounting location for your fog lights. Usually as mentioned above, these lights are placed on the bumper but place it as per your requirement and usage. It is advisable to put the fog lights temporarily first before you attach the lights permanently so that you can change it later if required.

Step 3: Switch Placement

After you have put the fog lights in the desired place, put the switch in a location which would be convenient to the driver to switch on and off. Now this step comes into picture only if you want an additional switch. If not, move onto the next step.

Step 4: Wiring the fog lights with a separate switch

The wire that comes from under the dash, connect that with the switch terminal on the lights. Now connect the battery terminal on the lights to the battery. Then connect the ground terminal on the switch to the metal part under the dash. After that, connect the load side of the switch with a wire. Take this wire through the firewall into the engine compartment and connect it to battery. After you are done with the wiring process, double check if all the wiring is secure. Re-connect the ground terminal of the battery.

Step 5: Wiring the fog lights with the headlight switch

Repeat the same process above. Only change here would be that you would have to connect the wires to the headlight switches instead. Connect two parts of the wire of the lights, one to the high end beam and the other to the low end beam.

Check everything again and test if the setup is working.

How To Wire Offroad Lights

Off-road lights are the lights for a vehicle which are designed specifically for different types of tasks which cannot be performed by headlights that well. Usually the Off-road lights are used when there is thick fog or there is heavy rainfall and the way ahead requires extra illumination to drive safely. It is even used at time for search and rescue. Off-road lights do not come fit in vehicles and are not commonly used. People who feel the need for it get it installed separately as it easily available.

Wiring Off-Road Lights can be simple if you follow proper steps and do not go haywire in the process. Always seek professional help if you are not good with electrical wiring. Below are some simple steps which will guide you on how to wire off-road lights:

Step 1: Disconnect Battery

First and foremost, disconnect the ground terminal on the battery as this is important for safety and for the connection of the lights as well.

Step 2: Mounting the lights

Decide the mounting spot for your off road lights. In case this is your first time and you are not sure which would be the ideal spot, as someone who knows how to wire off-road lights as they would have an idea. It is always a good idea to place the lights temporarily before you fix the lights so that you can change it later if required.

How to wire Off-road lights 1

How to wire Off-road lights 1

Step 3: Placing the switch

Once you have decided the spot of the off-road lights, place the switch in a location which would be convenient to the driver to switch on and off. Use the same trick here, place it temporarily making sure t can be changed if required as per the driver’s convenience.

Step 4: Wiring the Off-road Lights

The wire that comes from under the dash, connect that with the switch terminal on the lights. After this, connect the battery terminal on the lights to the battery. Now, connect the ground terminal on the switch to the metal part under the dash. Now connect the center lug of the switch with a wire. Take that wire through the firewall into the engine compartment and connect it to battery. Try keeping slightly extra length of the wire to move the switch around if required later. Once you are done with the setup, check if all the connections are secure. Connect back the ground terminal of the battery.

Step 5: Testing

Test by switching the lights on and off multiple times to ensure that the connection is secure and not loose.

To summarise the process, the lights have to be connected to the ground and to the switch. The switch has to be connected to the ground and to the battery. The battery has to be connected to the switch and the ground. This is an easy process if you even have slight experience with handling electrical wiring.

Best Fog Lights

Fog lights are lights which are designed specially to aid the driver see the road through the fog. The Fog lights are a unique beam shaped lights. They often come in a narrow bar shape. They have beams which are flat and are wide which allows maximum visibility in dense fog conditions. They are placed in the lower parts of the car which allows the driver to view the road. The Fog Lights are mainly placed on the bumper of the vehicle. The lights come in yellow and white color depending upon the rules and the use.

When buying a fog light, it is always a good idea to buy the best in class because it is a one-time investment and if you are fitting it on your own, it does require a lot of time as well.

A good idea to choose the best fog light is to ensure that it has a beam which is good enough to survive the dense fog and can even provide you with extra off-road features so that you do not have to get two separate lights unless you have extreme need for it.

The best fog lights that we have come across and are very popular and have garnered mostly positive reviews are as follows:

1. Nilight pot Driving Fog Light Offroad Led Lights Bar

Nilight Pot Driving Fog lights provide a Super Bright Spot Beam as it comes with high quality LED chips which emits bright white light. The concentrated spot beam of these lights can illuminate to a good distance.One of the best part about these lights it that it comes with adjustable mounting bracket which allows the drivers to adjust the light pods to about 45 degree which allows for an easy change of direction of the light beam as required. These fog lights are designed specially to last for about 30,000 hours which is higher than what other fog lights promise. This is possible because of the uniquely designed aluminum alloy cooling fins which gives durability to the lights.

PROS

  • The lights are waterproof up to 3.3 feet of water which helps if you are driving inwaterlogged areas.
  • The lights are dust proof which makes it even more low-maintenance and long lasting.

CONS

  • The mounting screws do not thread to the mount base completely and thus, requires youto do it.
  • The screws and bolts can be a little difficult to install.

#2. MICTUNING Curved LED Work Light Bar Combo Off Road DrivingFog Light

MICTUNING Curved LED Work Light Bar Combo is a dual feature light which gives you the bestof both types of lights.

It offers super clear visibility from its premium LED which can emit up to6000K crystal white light.

This gives you a bright light which is probably brighter than any otherlight in this category.

It is designed specifically to perform for vehicles which have to be driven inbad weather and road conditions.

It has a unique reflector cup which covers each LED andgives a farther reach to the light than any other LED gives. It offers an amazing combination ofspot/flood beam pattern and ensures that the light covers the maximum distance with the widestview.

It is suitable for any type of vehicle which includes Jeeps, ATVs, SUVs, 4x4 e.t.c.

It has aslightly curved design which fits perfectly with your car and makes it look attractive too.

It ismolded as per real car arc.

In addition to these features, it is resistant to corrosion and rustwhich adds up to the lifespan of these lights.

PROS

  • The lights come with a 2-year warranty.
  • It comes with 10pcs cooling pins which allows for maximum heat dissipation comparedto lights which comes with 8pcs.
  • It is waterproof as it has an aluminum housing and a heavy duty powder coat.

CONS

  • The lights can get moisture inside the glass at times which can reduce the lifespan of thelights. The lights get condensed easily.
  • It is prone to flickering if used in snow prone areas.

These are the top two choices by consumers all around the world when it comes to buying fog lights. They not only trust the light brands but have also found the lights to be durable and doingwhat they are supposed to do. Since these lights also perform the safety feature while driving, itis important that you analyse your requirements before actually buying these lights. Some states have laws and rules about adding additional lights to your vehicle so ensure that you check those before going ahead with the process. The best lights are those which not only give youthe perfect driving vision but also which can survive the worst of weather conditions and ask forlow maintenance.

How To Wire Led Light Bar To High Beam

If you want to wire a LED light bar onto a high beam, you need to ensure that you have the necessary tools on board with you. Since this can get a little technical, only attempt it if you are a 100% sure that you can finish it up after starting. If this is your first time, try and seek guidance from someone who has dealt with technical projects like this before. It is a relatively easy process but you need to careful as you do not want to ruin the light bar or hurt yourself.

In order to start with the process, after gathering the necessary tools, wire and other equipments, you need to place the led light bar on the desired location. Ensure that the location is sturdy and does not have a clacking surface as it will make the task difficult and your setting loose. After this, disconnect the negative terminal from your car battery before you start any other work on this. Mount the fuse inside the vehicle and attach with a bolt. The fuse should be placed such that the wire easily reaches the battery. Now, connect the ring terminal to the positive terminal of the battery.

Find your vehicle’s headlamp wiring. The light bar wire needs to be connected to it. There would be three plugs: the factory plug, the headlight plug and the harness plug. Connect the headlight plug to the headlight wire plug. The factory plug connects to your light bar.

After this, mount the switch on to the car by finding the way of the other wires. There is a firewall inside the car which reaches the engine bay. You need to get the switch wire via that inside the car. Sneak the wire in and place the switch in an area which is easily accessible by the driver.

Once that is done, connect the harness plug. If you are confused about the wiring, it is a slight bit complicated. The light bar is connected to the fuse and to the vehicle. The fuse is connected to the battery and to the switch for the light bar. The fuse is also connected to the relay of the vehicle. After you have ensured that all of this is connected, it is now time to attach back the negative terminal back in its place in the battery to give power to the whole set up.

It is now time to test if you were successful. Switch on the light bar and let it be on the high setting and see if the power is getting interrupted or is stable. If it is stable and does not flicker and goes off as soon as you switch it off, it means that your task is done.

Always ensure that the light bar you are using is in compliance with local traffic laws so that you do not violate any regulations while doing your setup.